Homepage  >  中文版
Contacts
Tel:86-755-83416111
Fax:86-755-83416961
E-mail:sales@szektech.com
Add: Building 3,No.3,West Area,Shangxue Technology City,Bantian,Longgang District,Shenzhen,China
  • Support
  • PCB etching process and process control
     
    Date :2017-8-15

     

    The process of printing a circuit board from bare board to displaying a line pattern is a process of more complex physical and chemical reactions. This paper analyzes its last step - etch. At present, the typical process of printed circuit board (PCB) processing is "graphic plating". That is, the outer part of the outer layer to be retained on the copper part, that is, part of the circuit part of the pre-plating layer of tin plating, and then chemically the remaining copper foil corrosion, known as etching.

     

    1.The type of etching

     

    It should be noted that there are two layers of copper on the board. In the outer layer of the etching process, only one layer of copper must be etched away, and the rest will form the final desired circuit. This type of graphic plating, which is characterized by the presence of copper plating layer only below the lead tin resist layer.

     

    Another method is the entire board are copper, photosensitive film outside the part is only tin or lead tin resist layer. This process is called "full board copper plating". Compared with the graphics plating, the biggest drawback of the whole board copper plating is the surface of the copper must be plated twice and etching must also be corroded them. So when the wire width is very fine will produce a series of problems. At the same time, side corrosion will seriously affect the uniformity of the line.

     

    In the printed circuit board outer circuit processing technology, there is another way, is to use the photosensitive film instead of metal coating to do corrosion layer. This method is very similar to the inner layer etching process, which can be seen in the etching process in the inner layer process.

     

    At present, tin or lead tin is the most commonly used corrosion layer, used in the etching process of ammonia etching agent. Amine etching agent is a commonly used chemical liquid, and tin or lead tin does not occur any chemical reaction. Ammonia etchant mainly refers to ammonia / ammonium chloride etching solution.

     

    In addition, in the market can also buy ammonia / ammonium sulfate etching liquid. The sulfate-based etching solution, after use, can be separated by electrolysis and can be reused. Because of its low corrosion rate, generally in the actual production is rare, but is expected to be used in chlorine-free etching.

     

    It was tested with sulfuric acid-hydrogen peroxide as an etchant to corrode the outer layer. This process has not been widely used in commercial sense due to many reasons, including economic and waste treatment, etc. Furthermore, sulfuric acid-hydrogen peroxide can not be used for the etching of lead-tin resist, which is not a PCB Outside the main method of production, so most people rarely ask.

     

    2.Etching quality and pre-existing problems

     

    The basic requirement for the quality of the etch is to be able to completely remove all the copper layers except the resist layer. In the strict sense, if the precise definition is to be made, the etch quality must include the consistency of the wire width and the degree of lateral erosion. Due to the inherent characteristics of the current corrosion solution, not only down and the left and right direction of the etching effect, so the lateral erosion is almost inevitable.

     

    The pitting problem is an item that is often discussed in the etch parameter, which is defined as the ratio of the lateral etch width to the etch depth, called the etch factor. In the printed circuit industry, it varies widely from 1: 1 to 1: 5. Obviously, small side erosion or low etch factor is the most satisfactory.

     

    The structure of the etching apparatus and the etching solution of the different components have an influence on the etching factor or the side erosion, or, in an optimistic manner, it can be controlled. The use of certain additives can reduce the lateral erosion. The chemical composition of these additives are generally trade secrets, their developers are not disclosed to the outside world.

     

    In many ways, the quality of the etch is as long as it has existed before the printed circuit board enters the etch machine. Because there are very close internal connections between processes or processes for printed circuit processing, there is no process that is not affected by other processes and does not affect other processes. Many of the problems that have been identified as the quality of the etch are actually present in the process of filming or even more.

     

    For the outer layer of the etching process, because it embodies the "back stream" is like most of the printed circuit board processes are prominent, so many of the problems are finally reflected in it above. At the same time, this is also because the etching is self-adhesive film, the beginning of a long series of photosensitive process in the last ring, after the outer graphics that transfer success. The more the number of links, the greater the likelihood of problems. This can be seen as a very special aspect of the printed circuit production process.

     

    In theory, the printed circuit into the etching stage, the graphics plating process in the processing of printed circuit, the ideal state should be: after plating copper and tin or copper and lead and tin thickness of the sum should not exceed plating The thickness of the photosensitive film, so that the plating pattern on both sides of the film "wall" block and embedded in the inside. However, the reality of production, the world's printed circuit board after plating, the coating graphics should be much thicker than the photosensitive graphics. In the process of electroplating copper and lead-tin, the problem arises because of the tendency of the coating to exceed the photosensitive film, resulting in a lateral stacking. In the top of the line covered with tin or lead tin resist to extend on both sides, forming a "along", a small part of the photosensitive film covered in the "along" below.

     

    Tin or lead-tin formation of the "edge" makes the film can not be completely removed when the photosensitive film clean, leaving a small part of the "residual glue" in the "along" below. & Quot; residual glue & quot; or & quot; residual film & quot; remains below the resist & quot; along & quot; will result in incomplete etching. Lines in the etching on both sides after the formation of "copper root", copper wire to narrow the line spacing, resulting in printed circuit board does not meet the requirements of Party A, and may even be rejected. Due to rejection will make PCB production costs greatly increased.

     

    In many cases, in the printing circuit industry, the residual film and the copper may form a stack in the etching solution and block it at the nozzle of the etching machine and the acid pump, and have to be shut down and cleaned , And affect the work efficiency.

     

    3. Equipment adjustment and the interaction with the corrosion solution

     

    In the processing of printed circuits, ammonia etching is a relatively fine and complex chemical reaction process. On the other hand, it is an easy job. Once the process up, you can continue to produce. The key is to start once the need to maintain a continuous working state, should not dry stop. The etch process relies heavily on the good working condition of the device. For now, regardless of what kind of etching fluid, you must use high pressure spray, and in order to obtain a more neat side of the line and high quality etching effect, you must strictly select the nozzle structure and spray.

     

    In order to get a good side effect, there have been many different theories that form different design patterns and equipment structures. These theories are often very different. But all the theories about etching recognize such a basic principle that the metal surface is kept in contact with fresh etch as quickly as possible. The chemical mechanism analysis of the etch process also confirms this view. In ammonia etching, assuming that all other parameters are not changed, the etch rate is mainly determined by the ammonia (NH3) in the etchant. So the use of fresh solution and etching surface, the purpose of the main two: First, washed away just generated copper ions; the second is to continue to provide the required ammonia (NH3).

     

    In the traditional knowledge of the printed circuit industry, especially the suppliers of printed circuit materials, it is recognized that the lower the content of monovalent copper ions in the ammonia etching solution, the faster the reaction rate. This has been confirmed by experience The In fact, many of the ammonia etching solution products contain a special copper (copper) complex (some complex solvent), its role is to reduce the price of copper ions (these are their products with high response ability of the technical tips ), We can see the impact of a copper ion is not small. Will be a price of copper from 5000ppm down to 50ppm, etching rate will be more than doubled.

     

    Since a large amount of monovalent copper ions are generated during the etching reaction, and since the monovalent copper ions are always tightly bonded to the complex of the ammonia, it is very difficult to maintain the content thereof near zero. The conversion of monovalent copper to divalent copper through the action of oxygen in the atmosphere can remove monovalent copper. Spray the way you can achieve the above purpose.

     

    This is a functional reason for passing air into the etch box. However, if the air is too much, it will accelerate the loss of ammonia in the solution and the PH value decreases, and as a result, the etching rate is lowered. Ammonia is also required in the solution to control the amount of change. Some users adopt the practice of passing pure ammonia into an etching reservoir. This must add a set of PH meter control system. When the automatically measured PH results below the given value, the solution will automatically add.

     

    In the field of chemical etching (also known as photochemical etching or PCH), the research work has begun and reached the stage of the structural design of the etch machine. In this method, the solution used is divalent copper, not ammonia-copper etch. It will likely be used in the printed circuit industry. In the PCH industry, the typical thickness of the etched copper foil is from 5 to 10 mils, and in some cases the thickness is quite large. Its requirements for etch parameters are often more severe than in PCB industry.

     

    4. On the upper and lower board, the import side and the back edge of the etching state of the problem

     

    A large number of problems related to the quality of the etch are focused on the etched part of the upper plate. It is important to understand this. These problems come from the impact of the upper plate etchant produced by the printed circuit board. The colloidal plate is deposited on the surface of the copper, which affects the spray force on the one hand and the addition of the fresh etchant on the other hand, resulting in a reduction in the etching rate. It is precisely because the formation and accumulation of the colloidal plate makes the upper and lower sides of the board different etching degree. This also makes the part of the board in the etching machine to easily enter the part of the etching is completely or easily lead to corrosion, because then the accumulation has not yet formed, the etching speed faster. On the contrary, the board into the part of the entry into the accumulation has been formed, and slow down the etching rate.

     

    5. Etching equipment maintenance

     

    Etching equipment maintenance of the most critical factor is to ensure that the nozzle clean, non-blocking material leaving the jet smooth. The obstruction or slag will impact the plate under the injection pressure. If the nozzle is dirty, it will cause uneven etching and make the whole block of PCB scrapped.

     

    Obviously, the maintenance of the equipment is to replace the damaged parts and wear parts, including the replacement of the nozzle, the same nozzle wear problems. In addition, the more critical issue is that there is no slagging in the etch machine, and in many cases slagging will occur, too much slag accumulation, and even affect the chemical balance of the etchant. Similarly, if the etching fluid appears excessive chemical imbalance, slagging will become more serious. The problem of how to emphasize the accumulation of slag is not too much. Once the etching fluid suddenly a lot of slagging situation, usually a signal, that is, the balance of the solution problems. This should be done with a strong hydrochloric acid for proper cleaning or addition of the solution.

     

    Residual film can also produce slag, a very small amount of residual film dissolved in the etching solution, and then the formation of copper salt precipitation. Residual film formed by the slag that before the road to the membrane process is not complete. Membrane failure is often caused by the edge of the membrane and over-plating results.

     

  • Tel:86-755-83416111   Fax:86-755-83416961   E-mail:sales@szektech.com   sitemap
  • Copyright 2014 © E-Tech (Shenzhen) Technology Ltd. All Rights Reserved